Multi-Family STC Ratings: Condo Soundproofing Building Code Requirements and Luxury Targets

Written By Pascal Fontaine-Ferrand

Blog | Builder Partnerships | Commercial Projects | Condos & Apartments | Residential

Multi-family STC ratings and the condo soundproofing building code in Ontario: OBC and NBC requirements, ASTC 47 field tests, IIC and luxury targets. (149 characters)

The building code minimum for sound between suites was never written to make a condo feel quiet. It was written to set a floor below which living next to someone becomes unreasonable. Multi-family STC ratings at that floor, STC 50 for the assembly or ASTC 47 in the field, still let a neighbour’s TV, a raised argument and every footstep overhead into the suite next door.

Buyers of a new condominium or a premium rental don’t compare your walls to the code. They compare them to the silence they expected for the price. That gap between compliance and expectation is where complaints, board disputes and warranty claims come from, and it’s decided on the drawings, long before anyone moves in.

This guide is for developers, estimators and site superintendents on multi-unit projects in Ontario. It’s written from our work as a single-source acoustic contractor for framing, insulation and drywall packages, and it covers what the code actually requires, what each rating sounds like, where field results are lost, and how to price the work so the acoustic scope survives the tender.

Condo Soundproofing Building Code: NBC and OBC Standards

Sound between dwelling units is regulated in the National Building Code of Canada (NBC) and, in Ontario, the Ontario Building Code (OBC), in Part 5 for larger buildings and Part 9 for houses and small buildings. Ontario amended its sound transmission requirements on January 1, 2020, and carried them into the 2024 OBC, which took effect January 1, 2025.

The Two Compliance Paths

Every dwelling unit must be separated from other dwelling units, and from other spaces in the building where noise can be generated, by one of two routes:

  • ASTC 47: the separating assembly and the adjoining constructions around it together provide an Apparent Sound Transmission Class of at least 47. ASTC counts all the sound that reaches the next suite, through the wall or floor and around it.
  • STC 50: the separating assembly alone provides an STC of at least 50, and the adjoining floors, walls and junctions are built to the code’s prescriptive details, which leave very little room for substitutions.

ASTC compliance can be shown by calculation from tested data, using the NRC Canada guidance, or by detailed construction to the code’s tables. In most Ontario jurisdictions, field testing is not a routine requirement on every project. It is common, though, when an acoustic consultant specifies it, when a developer wants proof before closings, or when a complaint turns into a dispute. Some municipalities also ask the designer to sign a sound transmission design declaration stating which path the building follows.

Higher Requirements Near Elevators and Chutes

Where a dwelling unit adjoins an elevator shaft or a refuse chute, the code raises the separating assembly to STC 55. Mechanical rooms, garage ramps, amenity spaces and commercial units at grade have no special number in the code beyond the general requirement, but they are where most serious noise complaints in mixed-use buildings start. Treat them as STC 55 to 60 zones in design, even where the code allows less.

Why the Shift to ASTC Matters

For decades, the code rated only the wall or floor between two units. A lab-tested STC 50 wall passed on paper even if sound walked around it through a continuous slab, a corridor wall or a window mullion. ASTC closes that loophole: it measures the building, not just the partition. For a developer, that turns flanking from a design afterthought into a compliance item.

Code requirements change between editions and can be amended locally. Confirm the edition and articles that apply to your permit with your architect, acoustic consultant or building official.

Code Minimum vs Luxury: STC 50 vs STC 58+

Ratings are easier to sell when you can describe what a buyer will hear. These are typical experiences, assuming normal background noise in the receiving suite. Quiet suites on high floors, with little traffic noise to mask anything, make every rating sound worse.

Performance tierLab STC targetField ASTC targetWhat the neighbour hearsMarket position
Field failureBelow 50Below 47Conversations and TV dialogue can be followed; phone calls are overheardBelow code; rework and disputes
Code baseline5047Loud speech audible but mostly not understood; bass, music and footfall come throughRental and entry-level product
Market standard5550 to 52Loud speech muffled; normal conversation privateMid-market and Class-A condominiums
Luxury specification58 to 62+55+Speech effectively gone; instruments and home theatre substantially reducedPremium condominiums and high-end rentals

No rating eliminates low-frequency bass from a subwoofer, which needs mass and isolation well beyond normal demising walls. What higher multi-family STC ratings do is move a building from “we hear our neighbours” to “we hear our neighbours occasionally,” and that difference shows up in reviews, resale and rental retention.

How the Higher Tiers Are Built

A single row of steel studs with insulation and double board on one side lands around the code baseline. Getting to STC 55 usually means adding board to both faces or decoupling one side with resilient channel or isolation clips. The luxury tier relies on staggered and double-stud separations, where the two faces of the wall share no studs at all, plus two layers of board each side and a fully insulated cavity. Exact ratings depend on the tested assembly, so always price against a published test, not a description.

Floor-Ceiling Assemblies: Airborne STC and Impact IIC

In multi-family buildings, the floor causes more complaints than the wall. People tolerate muffled voices; they don’t tolerate footsteps landing over their bed at midnight. Floors carry two kinds of sound:

  • Airborne sound (STC/ASTC): voices, television and music travelling through the air and the structure.
  • Impact sound (IIC): footsteps, dragged chairs and dropped objects striking the floor directly, measured as Impact Insulation Class.

The OBC sets airborne requirements between suites, but it does not require an IIC rating. Its appendix recommends at least IIC 55. In practice, that recommendation is where many disputes are settled, because buyers and condo boards treat it as the expected minimum even though the code doesn’t enforce it.

The Hard-Surface Problem

Concrete slabs are good at blocking airborne sound and poor at stopping impact. A bare slab rates far below IIC 55, and it’s the floor finish and what sits under it that close the gap. Carpet solves impact almost on its own, but today’s buyers want luxury vinyl plank, engineered hardwood and porcelain tile, which transmit footfall directly into the slab.

Two strategies work, usually together:

  • From above: a tested acoustic underlayment (rubber, cork or engineered foam) under the hard finish, specified as a system with that finish and slab thickness, with perimeter isolation strips so the floor doesn’t touch the walls.
  • From below: a drywall ceiling suspended on acoustic hangers or isolation clips, with insulation in the cavity, which decouples the ceiling from the slab or joists above.

In wood-frame and light-steel buildings, the ceiling below is not optional. Without a decoupled ceiling and an insulated cavity, no underlayment will bring a framed floor to a comfortable impact rating.

Multi-Family STC Ratings in the Field: ASTC and Flanking

It’s common for a wall rated STC 54 in a lab to test in the mid-40s on site. The wall hasn’t failed; the building around it has. A lab test (ASTM E90) measures one assembly mounted between two isolated rooms. A field test (ASTM E336) measures everything: the wall, the floor, the junctions and every hole between two suites.

The Four Flanking Paths That Sink Field Tests

  • Façades, curtain walls and window walls: continuous mullions and slab-edge gaps carry sound past the end of the demising wall. The wall must meet the façade with a sealed, insulated closure, and the mullion itself may need an acoustic treatment.
  • Continuous floors and corridor walls: sound travels through slabs, toppings and walls that run unbroken from one suite to the next. Heavy concrete flanks less than lightweight framing, but a gap under the base track or at the head of the wall wipes out the advantage.
  • HVAC and shared plenums: ducts, fan coil enclosures and bulkheads that cross a demising line act as speaking tubes. Each suite should have its own runs, and any crossing needs lining, silencers or a sealed sleeve.
  • Plumbing and electrical penetrations: back-to-back outlets, unsealed pipe sleeves, recessed medicine cabinets and shared low-voltage conduit all punch holes through an otherwise good wall.

Inside the wall, the cavity matters too. Acoustic batts between units absorb sound in the stud space and damp the cavity resonance, but they have to fill it completely, top to bottom, with no gaps at boxes and backing. And the perimeter has to be airtight: acoustic sealant at the top and bottom tracks, at both ends and around every penetration, applied before the board goes on and again at the face.

Preparing for Field STC Testing and Pre-Occupancy Inspection

A field test under ASTM E336 is straightforward to watch and unforgiving to fail. A calibrated loudspeaker produces loud broadband noise in the source suite. Microphones measure the level in that room and in the receiving suite, and the background noise is recorded. The receiving room’s absorption is measured, the results are calculated across the frequency range, and the ASTC is reported as a single number.

Tests are best done after drywall, doors and finishes are in but before suites are furnished, when there’s still time to fix what’s found. A failed result, on a project where testing is required by the specification or the consultant, means investigation, rework and retesting, and that can push back occupancy, closings and condo registration.

The Pre-Test Walkthrough

Most field failures can be found with a flashlight before the test is booked:

  • Top of wall: confirm the demising wall reaches the slab or deck above, with a continuous seal; check bulkheads and drop ceilings that hide the head of the wall.
  • Base track: look for gaps under the track and at floor transitions, especially at corridor walls.
  • Boxes and penetrations: no back-to-back outlets in the same stud bay; putty pads on every box; sealed sleeves on every pipe and conduit.
  • Façade junction: sealed closure where the demising wall meets the exterior wall or window wall.
  • Entry doors: suite entry doors gasketed, with a drop seal or threshold, so the corridor doesn’t become the flanking path between suites.
  • Mechanical crossings: no shared ducts or open plenums across the demising line.

FROM THE FIELD

In condo work, three things cause most of the noise complaints we see.

The worst is the gap under the suite entry door. Every sound in the hallway comes straight through it, and there’s no real privacy at the door. The gap is there on purpose: the corridor ventilation system pushes air into the suites through it, and it’s part of how the building manages air and smoke in a fire. That means there’s no legal fix. Suite entry doors are fire-rated and usually belong to the condo corporation, and anything that blocks the gap gets removed at the annual fire inspection.

The second is what the industry calls a “double leaf”: two hard surfaces with an empty air gap between them and no insulation. In condos, it’s usually the concrete party wall, then wood strapping, then drywall. That empty cavity resonates like a drum and can make the noise coming through the concrete worse, not better. Filling the cavity with insulation, or decoupling the drywall, stops the drum effect.

The third is back-to-back outlets: two electrical boxes in the same spot on either side of the wall, which leaves a hole in it. We seal those boxes with putty pads.

Estimating Acoustic Assemblies for Multi-Family Tenders

On most multi-unit tenders, the acoustic scope is lost in the details rather than the headline assembly. The wall type on the drawings gets priced; the work that makes it perform gets missed, value-engineered out, or left between trades.

Where the Cost Difference Comes From

Moving from a code-baseline single-stud partition to a STC 58+ double-stud assembly roughly doubles the framing and adds board, insulation and labour. Per linear foot, the main drivers are:

  • Framing: a second row of studs and tracks, or resilient channel and clips, plus the extra layout and fastening time.
  • Board: additional layers on one or both faces, with staggered joints and more taping.
  • Insulation: a second cavity to fill on double-stud walls.
  • Thickness: wider walls take floor area from every suite, which developers should weigh against the price premium the quieter suites support.

The Hidden Line Items

These are the items that separate a wall that passes a field test from one that doesn’t. Price them as their own lines so they can’t disappear:

  • Acoustic sealant at top and bottom tracks, wall ends and every penetration, on both faces
  • Putty pads on every electrical box in a demising or corridor wall
  • Isolation clips, resilient channel and acoustic ceiling hangers, with the extra labour they take
  • Perimeter isolation strips and the coordination with flooring trades
  • Façade and slab-edge closures where demising walls meet the exterior
  • Bulkhead and top-of-wall details where ducts or sprinklers cross the demising line
  • A pre-test walkthrough and repair allowance on projects where field testing is specified

Why One Trade Should Own the Wall

When framing, insulation and drywall are split between subcontractors, every acoustic detail sits on a boundary: who seals the track before the board goes on, who fills the cavity at the boxes, who fixes the gap at the head of the wall. Single-source contracting removes those boundaries. One crew builds the wall from track to tape, inspects its own details before close-up, and owns the result if a test comes back low.

Frequently Asked Questions

What is the difference between lab STC and field ASTC in Ontario?

STC is measured in a laboratory under ASTM E90, on one wall or floor mounted between two isolated rooms. ASTC is measured in the finished building under ASTM E336 and includes all the sound that reaches the next suite, through the assembly and around it by flanking paths. The OBC accepts either STC 50 built with prescriptive adjoining details, or ASTC 47 for the assembly and its surroundings together.

Can a condominium board enforce soundproofing standards stricter than the Ontario Building Code?

Yes, within limits. A condominium’s declaration and rules can require board approval before owners replace flooring, and can set a minimum underlayment or impact rating for hard-surface floors. Rules have to be reasonable and consistent with the Condominium Act, so boards usually rely on their own lawyers to word them. These rules govern renovations by owners; the building itself still only has to meet the code.

How do back-to-back electrical outlets in demising walls affect the STC rating?

They can cut it noticeably. Two boxes in the same stud bay, one on each side, leave only the box walls between suites, and a thin metal or plastic box is far weaker than the wall around it. Offset boxes by at least one stud bay, seal each one with a putty pad, and keep the insulation tight around them.

What floor underlayment is required to achieve IIC 55 over a 6-inch concrete slab?

There’s no single answer, because IIC depends on the whole system: slab, underlayment, finish and the ceiling below. A bare 6-inch slab rates far below IIC 55. With hard finishes, you’ll typically need an acoustic underlayment that has been tested over a similar slab with the same type of flooring, and sometimes a suspended ceiling below as well. Ask the manufacturer for the test report for that exact build, not a generic rating.

Submit Multi-Family Plans for Tender Review

Make sure your multi-residential development is built to pass on the first test. Inaudible provides turnkey framing, insulation and drywall packages built for code compliance and premium acoustic targets. Send us your architectural drawings and acoustic specifications, and we’ll review the demising and floor-ceiling assemblies, flag the flanking details most likely to fail, and price the package with every acoustic line item included.Submit Plans for ReviewCall (416) 466-1476

GCSI 09 21 16 GYPSUM BOARD ASSEMBLIES

More Posts